Ø Based on self -copyright IC
Ø Canrealize monitor and control of remote equipment, OAM management data did not take up user’s timeslot and save E1 bandwidth
Ø E1 supports any timeslot set, the rate is 64K-2048K
Ø The local device can forced the remote device rate follow it
Ø Have the function of E1 interface loop back check,avoid the converter crashed because of interface loop return;

Ø Have indicator whenthe device is power-off or E1 line is broken or lose signal;
ØCan set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
Ø The Ethernet interface supports jumbo frames (2036 Bytes);
Ø Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering
Ø Ethernet interface supports10M/100M,half/full duplex auto- Negotination and AUTO-MDIX(crossed line and straightly connected line self-adaptable );
Ø Have Ethernet monitor self-reset function, the equipment will not dead
Ø Can achieve the remote device setting any 5 mode of Ethernet and can closed the AUTO-MDIX function;
Ø Provide 2 clock types: E1 master clock and E1 line clock;
Ø Havethree Loop Back Mode: E1 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote Ethernet interface Loop Back(REM)

ØProvide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
Ø SupportSNMP Network Management;
Ø Can realize monitor of remote equipment temperature and voltage from local equipment;

Ø Can form the structure: Ethernet E1 Bridge(A)－－-E1 Optical Fiber Modem(B)－－-Ethernet Optical Fiber Modem (C)
Ø Can form the structure: Ethernet E1 Bridge(A)－－-Optical Ethernet Modem(B)－－-Ethernet Optical Fiber Transceiver (C), can manage (B) and (C) at (A)

Technical parameters：

E1 Interface	Interface Standard: comply with protocol G.703; Interface Rate: n*64Kbps±50ppm; Interface Code: HDB3; E1 Impedance: 75Ω (unbalance), 120Ω (balance); Jitter tolerance: In accord with protocol G.742 and G.823 Allowed Attenuation: 0~6dBm
Ethernet interface (10/100M)	Interface rate: 10/100 Mbps, half/full duplex auto-negotiation Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN) MAC Address Capability: 4096 Connector: RJ45, support Auto-MDIX
Power	Power supply: AC180V ~ 260V；DC –48V；DC +24V Power consumption: ≤3W
Dimension	Product size: 216 X138 X31 mm(WXDXH) Simple packaging: 274X193X84 mm (WXDXH) Piece weight : 1.1KG
Working environment	Working temperature: -10°C ~ 50°C Working Humidity: 5%~95 % (no condensation) Storage temperature: -40°C ~ 80°C Storage Humidity: 5%~95 % (no condensation)

Networking Application

Application

Application one

Description:

The network card of one or more PC machines (A Point) connect to the Ethernet switch Ethernet interface. That connects via connecting Ethernet switch UP Link interface with 10/100Base-T interface of FE1-10/100Base-T interface converter through the transmission of E1 and Ethernet data of Ethernet switch (B Point), after converting to fiber, transmitting to Optical Fiber Transceiver(C Point),then with user’s PC machine andother equipment realize communication function between three points.

1. Interface converter use in pairs;

< >The device mode is framing mode. E1 Transmission Circuit Bandwidth is 2.048M. It can manage (B) and (C) at (A)

Application two

Description:

The network card of one or more PC machines (A Point) connect to the Ethernet switch Ethernet interface. That connects via connecting Ethernet switch UP Link interface with 10/100Base-T interface of FE1-10/100Base-T interface converter through the transmission of E1 and Ethernet data of E1 fiber mode (B Point), after converting to fiber, transmitting to Optical Fiber Transceiver(C Point),then with user’s PC machine andother equipment realize communication function between three points.

< >Interface converter use in pairs;The device mode is framing mode. E1 Transmission Circuit Bandwidth is 2.048M. It can manage (B) and (C) at (A)

Application three

Description:

The network card of one or more PC machines (A Point) connect to the Ethernet switch Ethernet interface. That connects via connecting Ethernet switch UP Link interface with 10/100Base-T interface of FE1-10/100Base-T interface converter through the transmission of E1 and Ethernet data of Ethernet optical port interface converter (100BaseT-FX)(B Point), after converting to fiber, transmitting to Optical Fiber Transceiver(C Point),then with user’s PC machine and other equipment realize communication function between three points.

< >Interface converter use in pairs;The device mode is framing mode. E1 Transmission Circuit Bandwidth is 2.048M. It can manage (B) and (C) at (A)

Specifications：

1.Wide industry application . to expand special function according to different industries

Dual power supply option with power on/off alarm

2.High Resolution Display Quality.

3. Adopt imported master chip
4.High quality,High performance
4.Low consumption
5. Fatory price

Our service

1. The good construction warranty-2years
2. Your client satisfied on the right schedule and quality
3. You can get a good reputation from your market and obtain more orders
4. Our professional service before and after sale
5. The reasonable price
6. Any query from you are welcome and will be replied within 24 hours.

Note:

superior performance, abundant functions, easy operation, high accountabilityand a complete range of specifications.Can fully meet the individual needs of customers in the industry.

OR, you can tell us your requirements, so that we could offer you the customized service!!

Welcome to cooperate with us, we will serve you wholeheartedly!

Any interests,plz contact us without hesitate!www.fctel.com.cnSkype:Soda.wu Wechat:Sodawujun

Engineering and production departments both feature extensive on-site testing equipment to verify that all products exceed pertinent industry and environmental specifications.

 

 

Fibreasy products are CCC compliant and are manufactured and produced in the HANGZHOU city of China. Fibreasy company also operates a Quality Management System as compliant with ISO9001:2008 requirements